Leakage Current and Grounding Anomalies in Servo Presses: Troubleshooting Sequence

2021-02-24 2026-11-13 admin 200 Company News and Technical Insights, Maintenance and Troubleshooting
伺服电动缸实拍

Key Conclusions:It is common for servo drives to exhibit high-frequency leakage current flowing through EMI filter capacitors to protective ground, which is a normal occurrence; however, a live chassis or frequent tripping of the ground fault circuit interrupter (GFCI) constitutes a malfunction and should be troubleshot by following a four-step process covering the power supply, grounding, cabling, and motor.

Basis for Identifying State Changes

First, check whether the protective grounding connection is secure. Excessive grounding resistance is the most common cause of a live chassis and is also the most easily overlooked.

The higher the carrier frequency of the servo drive and the longer the motor cable, the greater the distributed capacitance to ground, and the higher the leakage current.

Routine Inspections and Preventive Maintenance

  • Standard ground-fault circuit interrupters (GFCIs) are prone to false trips; in industrial settings, it is advisable to select models that are insensitive to high-frequency components or to adjust the settings according to the manufacturer’s recommendations.
  • Damage to the insulation of motor power cables or moisture in the connections can cause a decrease in actual insulation resistance; therefore, it is necessary to measure each section with a megohmmeter rather than relying solely on error codes.
  • Do not disconnect the protective grounding to prevent a trip; doing so compromises both EMC and personal safety.

Common Alarms and Troubleshooting Steps

Phenomenon Prioritize Investigation
Significant positional error Mechanical jamming, acceleration/deceleration parameters, encoder feedback, workpiece interference exceeding limits
Busbar Overvoltage Deceleration Time, Load Inertia, Braking Resistor Power, and Resistance
Curve Jitter Power and signal lines run together; shielding grounded at both ends; ground loop current
Accuracy Drift Temperature rise in the lead screw, lubrication degradation, loose fixtures, sensor zero point

Related Equipment and Further Reading

Apply the above parameters to a specific device to verify them. We recommend referring to the following as well:Servo Press Motor Rotor Press-Fit Machine、Positioning Pins and Steel Ball Press-Fit Equipment、High-Speed Chain Automated Assembly Line。

For systematic principles and selection methods, see The Complete Guide to Servo Presses; For a complete list of models and specifications, see Product Center。

Frequently Asked Questions

Is a slight tingling sensation on the case a sign of normal leakage current?

No. Normal high-frequency leakage current should not cause a perceptible electric shock; you must check the grounding and insulation.

If a ground fault circuit interrupter trips, can it be replaced directly with one rated for a higher current?

No, you must first locate the source of the ground fault; otherwise, you’ll mask the insulation failure.

If you need to calculate thrust, stroke, or the determination window based on your workpiece, or if you would like to request technical documentation, please visitDownload Product Brochures、prescription, or directly through Contact Us Submit your operating conditions, and engineers from Shanghai WINTRL Automation will provide product selection recommendations. For company background, seeAbout Us。

Related Articles

伺服压机实拍
Is the servo electric cylinder the core component of a servo press? Its Function and Selection Criteria 2021-06-03
WL 系列电缸实拍
How to Operate a Servo Press? A Standard Press-Fitting Process and Parameter Settings 2021-03-26
设备触摸屏实拍
What Is a Pressure Sensor in a Servo Press? Measurement Range, Accuracy, and Installation Guidelines 2021-03-26
Technical Features of Servo Electric Cylinders: How to Interpret Thrust, Stroke, and Repeatability 2021-02-24
What Causes Temperature Rise in Servo Presses? The Actual Impact on Precision and Service Life 2021-02-24
How to Program Multi-Stage Pressing? Staged Stroke Control for Servo Presses 2020-11-24
Why Can Servo Presses Meet the Process Requirements for Precision Assembly? 2020-11-24
Why Can Servo Presses Replace Traditional Pneumatic and Hydraulic Press-Fitting Systems? 2020-10-08